Sterilizer: All American 75x Sterilizer - 110v and 220V

This sterilizer also has no special maintenance. What you have to do is just add water, and run it.

This sterilizer makes it possible for all doctors, dentists, first aid stations, hospitals and laboratories to have dependable sterilization facilities in a portable unit at an extremely low cost.

With Using only a small amount of water, it's only a matter of minutes to dry sterile dressings and instruments, with all bacteria and micro-organisms destroyed. At a temperature of 250F at 15 PSI, the dry steam makes bandages and instruments sterile and ready for immediate use. There is no chemical residue or moisture to remove, and cutting edges are not dulled.

All-American Sterilizers are made of high quality cast aluminum alloy, with all the special features of the famous All-American Pressure Canners. The metal-to-metal seal eliminates all rubber gaskets.

The clamping locks will prevent removal of the cover while pressure is present. An accurate pressure gauge, pressure control valve, over-pressure safety plug, and cool bake-lite handle and wing nuts are all thoroughly tested features that assure safe operation with a minimum of attention.

Description of All American 75x Sterilizer:

• 30/40 minutes complete cycle
• Built in timer
• Overall height 19"
• Chamber dimensions 14" dia x 10.5" deep
• Chamber inner capacity (inside tray) 25.8 liters, and outer capacity (without tray) 39 liters
• Voltage 110V
• Weight 45#
• Heavy Cast Aluminum Cover and Bottom Construction
• Aluminum Alloy Seamless Inset Container
• Cast Aluminum Rack
• Flexible Metal Exhause Tube
• Metal-To-Metal Seal (no rubber gasket)
• Complete/Effective Sterilization at the Lowest Possible Cost
• 3 Wire Grounded Plug for Safety
• Maximum Pressure 20psi

Specifications of All American 75x Sterilizer:

• Chamber Size: 14" Diameter and 10" Deep
• Brand New Machine
• Manual (electronic) controlled
• Steam Sterilizer
• Power Supply: 110V
• 45 minutes cycle
• Table Style
• Weight: 51.00 Pounds.

You can order this All American 75x Sterilizer - 110V and 220V here

Read more...

Sterilizer: All American Sterilizer 50X - 30/40 minute cycle - 110V and 220V

The sterilizer does not need any maintenance. The operation is simple and very easy. You just add water, and run it. All-American Sterilizers make it possible for all doctors, dentists, first aid stations, hospitals and laboratories to have dependable sterilization facilities in a portable unit at an extremely low cost.

Using only a small amount of water, it's only a matter of minutes to dry sterile dressings and instruments, with all bacteria and micro-organisms destroyed. At a temperature of 250F at 15 PSI, the dry steam makes bandages and instruments sterile and ready for immediate use.

There is no chemical residue or moisture to remove, and cutting edges are not dulled. All-American Sterilizers are made of high quality cast aluminum alloy, with all the special features of the famous All-American Pressure Canners. The metal-to-metal seal eliminates all rubber gaskets.

This sterilizer also has clamping locks to prevent removal of the cover while pressure is present. So it has a safety feature. An accurate pressure gauge, pressure control valve, over-pressure safety plug, and cool bake-lite handle and wing nuts are all thoroughly tested features that assure safe operation with a minimum of attention.


The model 50X has a 1650 watt heating element, compared to the Model 25X which has a 1050 watt heating element. This increased heating capacity means that the units will get up to operating temperature far quicker than the 25X.

The Model 50X has all new electrical controls and the thermostat is designed to hold a much tighter operating band over the 25X. Therefore, there will be less variation as the thermostat turns the heating element on and off to maintain a certain level of heat.

Furthermore, the 50X includes a mechanical timing device on the control box. All in all, the 50X offers added value and greater capacity.

Description Sterilizer 50X - 30/40 minute cycle:

• 30/40 minutes complete cycle
• Built in timer
• Overall height 16 3/4"
• Chamber dimensions 11.125" dia x 8.5" deep
• Chamber inner capacity (inside tray) 13.7 liters, and outer capacity (without tray) 24 liters
• Voltage 110V
• Weight 29#
• Heavy Cast Aluminum Cover and Bottom Construction
• Aluminum Alloy Seamless Inset Container
• Cast Aluminum Rack
• Flexible Metal Exhause Tube
• Metal-To-Metal Seal (no rubber gasket)
• Complete/Effective Sterilization at the Lowest Possible Cost
• 3 Wire Grounded Plug for Safety
• Maximum Pressure 20psi
• 20-25 minutes to heat up

Specifications Sterilizer 50X - 30/40 minute cycle:

• Chamber Size: 11" Diameter and 8" Deep
• Brand New Machine
• Manual (electronic) controlled
• Steam Sterilizer
• Power Supply: 110V
• 45 minutes cycle
• Table Style
• Weight: 34.00 Pounds.

You can order this All American Sterilizer 50X - 30/40 minute cycle - 110V and 220V here

Read more...

Sterilizer: All American 25X Sterilizer 110V and 220V– New

This is a new sterilizer that requires no maintenance. What you have to do is just add water, and run it. This is a25X-110V electric sterilizer that has 25 quart liquid capacity.

All American 25X Sterilizer 110V is a portable unit that will quickly pay its low cost in the saving of time alone. You do not need to purchase any additional supplies. And there is no any maintenance cost other than electric power consumed.

The sterilizer is made of high quality cast aluminum alloy, with all the special features of the famous All-American Pressure Cookers. The portable electric automatic sterilizer meets all requirements for physicians, dentists, first aid stations, hospital and laboratories.

The All-American Sterilizer has an automatic system in operation, controlled by a Fenwal thermostat of 250 degrees F. or 15 P.S.I., it penetrates the bandages or instruments, making them sterile in 30 minutes and all bacteria and micro-organisms are destroyed.

The sterilization time is counted when temperature and pressure levels are reached.

Description of 25X Sterilizer 110V:

• Overall height - 16 3/4"
• Chamber Dimension - 11.125" dia x 8.5" deep
• Chamber inner capacity (inside tray) 13.7 liters, and outer capacity (without tray) 24 liters
• Voltage 110 1050W
• 40-45 minutes to heat up
• Weight 29#
• Heavy Cast Aluminum Cover and Bottom Construction
• Aluminum Alloy Seamless Inset Container
• Cast Aluminum Rack
• Flexible Metal Exhaust Tube
• Metal-To-Metal Seal (No Rubber Gasket)
• Complete/Effective Sterilization at the Lowest Possible Cost
• 3 Wire Grounded Plug for Safety
• Maximum pressure 20psi
• Maximum temperature 259 f

Specifications of 25X Sterilizer 110V:

• Chamber Size: 11" Diameter and 6" Deep
• Brand New Machine
• Manual (electronic) controlled
• Steam Sterilizer
• Power Supply: 110V
• 45 minutes cycle
• Table Style
• Weight: 33.00 Pounds.
  

You can order this 1925X 1941X Sterilizer - Non Electric here

Read more...

Sterilizer: All American 1941X Sterilizer - Non Electric

All American 1941X non-electric cast aluminum sterilizer has 41.5 quart liquid capacity.

It makes it possible for all doctors, dentists, first aid stations, hospitals, and laboratories to have fool-proof sterilization facilities at an extremely low cost.

Description of 1941X Sterilizer - Non Electric

• Overall height 16 3/4"
• Chamber dimension 14" dia x 10.5" deep
• Chamber inner capacity (inside tray) 25.8 liters, and outer capacity (without tray) 39 liters
• Weight 41 Lbs
• Non-electric
• Maximum pressure 20psi
• Maximum temperature 259 f
• Calibrated Gauge
• Safety locking mechanism that prevents opening while the sterilizer is under pressure
• Steam Release Switch
• Heating source is needed to run this sterilizer. You may put it on a hot plate, or on a stove

Specifications of 1941X Sterilizer - Non Electric :

• Chamber Size: 14" Diameter and 10" Deep
• Brand New Machine
• Manual (electronic) controlled
• Steam Sterilizer
• Power Supply: No electric power
• 45 minutes cycle
• Table Style
• Weight: 44.00 Pounds.

You can order this 1925X 1941X Sterilizer - Non Electric here

Read more...

Sterilizer: 1925X New Non Electric V Sterilizer

This sterilizer is one sterilizer that has large sterilizing capacity. Complete and effective sterilization at the lowest possible cost and it is packed in individual corrugated cartons.

This 1925X New Non Electric V Sterilizer makes it possible for all doctors, dentists, first aid stations, hospitals, and laboratories to have fool-proof sterilization facilities at an extremely low cost.

With using over any effective heat source, it needs minutes to secure dry sterile dressings and instruments, and all bacteria and micro-organisms are destroyed.

How to use this sterilizer? And what do you need to operate this sterilizer?
It is simple and easy to use. The only a small amount of water is needed to create the dry steam. At a temperature of 250 degrees F. or 15 P.S.I., it penetrates bandages, hinges and crevasses in any instrument making them sterile in 30 minutes and ready for immediate use.

The Sterilization time is counted begins when temperature and pressure levels are reached.
No wiping is necessary to remove chemical residue or moisture, and cutting are not dulled. UL approved.

Description of This Sterilizer:

• Overall height 16 3/4 inches
• Chamber dimension 11.125" dia X 10.25" deep
• Chamber inner capacity (inside tray) 13.7 liters, and outer capacity (without tray) 24 liters
• Weight 24 Lbs
• Non-electric
• Maximum pressure 20psi
• Maximum temperature 259 f
• Calibrated Gauge
• Safety locking mechanism that prevents opening while the sterilizer is under pressure
• Steam Release Switch
• Heating source is needed to run this sterilizer. You may put it on a hot plate, or on a stove

Main Specifications:

• Chamber Size: 11" Diameter and 10" Deep
• Brand New Machine
• Manual (electronic) controlled
• Steam Sterilizer
• Power Supply: No electric power
• 45 minutes cycle
• Table Style
• Weight: 25.00 Pounds.

You can order this 1925X New Non Electric V Sterilizer here

Read more...

Sterilizer: 1915X New Non Electric V Sterilizer

Description of This Sterilizer

• Overall height 12 1/4"
• Chamber dimension 11.125" dia X 5.75" deep
• Chamber inner capacity (inside tray) 9 liters, and outer capacity (without tray) 14 liters
• Weight 20 Lbs
• Non-electric
• Maximum pressure 20psi
• Maximum temperature 259 f
• Calibrated Gauge
• Safety locking mechanism that prevents opening while the sterilizer is under pressure
• Steam Release Switch
• Heating source is needed to run this sterilizer. You may put it on a hot plate, or on a stove

How to use this sterilizer:

• It is just simple and very easy
• Put water in the chamber, and place the sterilizer on a hot plat
• That is it.

Specifications of This Sterilizer:

• Chamber Size: 11" Diameter and 6" Deep
• Brand New Machine
• Manual (electronic) controlled
• Steam Sterilizer
• Power Supply: No electric power
• 45 minutes cycle
• Table Style
• Weight: 20.00 Pounds.

You can order this new 1915X New Non Electric V Sterilizer here

Read more...

Laboratory Equipment: WTM-1000 Wind Tunnel

This is a new WTM-1000 mini wind tunnel comes from OMEGA®. It gives a highly uniform flow rate at 4 selectable fixed air speeds, yet it costs less than competitive brands. The machine has fixed air speeds range from 2.5 m/s (492 fpm) to 15 m/s (2953 fpm).

This laboratory equipment also has the remote option in witch the user can control and vary the wind tunnel air speed externally by connecting a potentiometer. The internal 10 cm (4") diameter test chamber is large enough to accommodate either hot-wire or vane-type anemometers.

The unit is powered by 90 to 250 Vac. Each WTM-1000 comes with an NIST calibration certificate for the 4 fixed air speeds.

Specifications New Wtm-1000 Mini Wind Tunnel:

• Accuracy: 1% of setting or 0.1 m/s, whichever is larger
• Test Chamber: 10 cm (4") diameter
• Flow Rates: 2.5 m/s (492 fpm), 5.0 m/s (984 fpm), 10 m/s (1969 fpm), 15 m/s (2953 fpm)
• Remote Option: Use an external 5K, 10-turn potentiometer to vary air speed
• DC Motor: 24 Vdc @ 1.1 A (26 W)
• Power: 90 to 250 Vac @ 50/60 Hz
• Operating Temperature: 5 to 45 °C (41 to 113°F)
• Operating Relative Humidity: 80% RH max without condensation
• Size: 68.5 L x 20.3 W x 29.2 cm H(27 x 8 x 11.5")
• Weight: 8.2 kg (18 lb)

If you need this machine/unit, you can contact here:

UNITED STATES
www.omega.com
1-800-TC-OMEGA
Stamford, CT.

CANADA
www.omega.ca
Laval(Quebec)
1-800-TC-OMEGA

GERMANY
www.omega.de
Deckenpfronn, Germany
0800-8266342

UNITED KINGDOM
www. omega.co.uk
Manchester, England
0800-488-488

FRANCE
www.omega.fr
Guyancourt, France
088-466-342

CZECH REPUBLIC
www.omegaeng.cz
Karviná, Czech Republic
596-311-899

BENELUX
www.omega.nl
Amstelveen, NL
0800-099-33-44

Read more...

Anesthesia Machine: FHC-EXCEL 210

Ohmeda Excell 210 Anesthesia Machine
The FHC-EXCEL 210 is an all-pneumatic alternative for close quarters. This unit has o2, n2o, and medical air standard. Also standard are hypoxic guard and a gms absorber. Drawer pack configurations may vary from picture.

This anesthesia Machine has special features:

• Compact Frame. Fits Space-Constrained Areas
• Integrated Oxygen, Volume, Airway Pressure Monitoring
• Enclosed, Non-Interchangeable Pneumatic Monitoring
• Differentiated Pipeline, Cylinder Gauges
• Master On/Off Switch; Acti8vates Electronics And Pneumatics
• Link-25 Hypoxic Mixture Guard System
• Pin-Indexed, Gas-Specific Dual O2 And N2o Flow Meters
• Selectatec Vaporizer Manifold For Two Tech 5 Vaporizers
• Guarded O2 Flush Button
• Oxygen Power Outlet
• Fixed Shelving With Added Monitoring Space
• Two-Drawer Storage Cabinet
• Single-Action Brake/Footrest
• Full-Height Dovetail Accessory Mounting System
• Large, Easy-Running Casters

Other Description of this Anesthesia Machine:
Weight: 300 Lb (136 Kg)
Height: 66" (168 Cm)
Width: 22" (550.87 Cm)


Maximum Load: 24 Lb (11 Kg)
Middle Shelf Size: 18.6" X 12.5" (47.2 Cm)
Usable Height: 6" (15.2 Cm)

Top Shelf:
Max Shelf Load: 48 Lb (22 Kg)
Size: 23.5 "X 14.2" (59.6 X 36 Cm)

Table Top:
Height From Floor: 33.5" (85 Cm)
Size: 21.7 X 11.5 (55.2 X 29.2 Cm)

Drawer Cabinet: Contains Two 10.5" X 15: X 4" (26.7 Cm X 38 Cm X 10.2 Cm) Drawers
Absorber Arm Length: 14" (3535 Cm)
Vertical Adjustment From Floor: 10" To 26" (25.4 Cm To 66 Cm)
Horizontal Adjustment: 6.5" Min; 11" Max (16.5 Cm Min; 27.9 Cm Max)
Casters: Diameter 5" (12.7 Cm)
Brakes: Brake Bar Lock On Front Casters; Operated By Foot Bar

Read more...

Star 50 – Portable Patient Monitor

The Star 50 was produced by larsen & turbo limited. It is a portable vital signs patient monitor. With this monitor you that can measures ECG, Respiration, SpO2, Non-invasive Blood Pressure and Temperature or your patient. Measuring CO2 can be added as optional at an additional cost.

Before you or your health care owner buy this star 50 patient monitor, it is advisable to see the features of this product. Here are the Product Features:

• High resolution 6.4" (diagonally) color TFT display
• Optional in-built dual channel thermal array recorder
• User selectable screen formats
• 24 hour data storage facility in tabular and graphical mode with zoom facility and separate tabular trend for NIBP to store and view last 240 readings
• Displays NIBP measurement, SpO2 values, PR, plethysmograph along with perfusion bar indicator
• Graded and color coded audio/visual alarms
• Programmable Arrhythmia package
• Cautery and defibrillator protection
• Comprehensive patient data entry
• Can be interfaced to L&Ts central station - Skyline
• Demo mode for training the staff
• Facility to interface to an external Slave monitor - Remote display (optional)
• External battery jack (12V) for car battery - Transport application
• Can be mounted on bed rail - Transport application

This Star 50 Patient Monitor has warranty Year factory and increase to 3 Year warranty for $500.00 additional
The package of The Star 50 Patient Monitor includes:
• One Reusable Adult Finger Clip Sensor
• 4 Size AA Alkaline Batteries
• Operator's Manual

You can buy this Patient Monitor through this site

Read more...

Ultrasonic Flowmeter FD-7000

Up to now, Doppler ultrasonic flow meters have required significant quantities of suspended particles or gas bubbles to reflect sound signals. Now, with the Model FD-7000 Ultrasonic Flowmeter, this is no longer required. When the FD-7000 is used to measure the flow of liquids containing suspended solids or bubbles, the transducers are mounted on a straight run of pipe in the same manner as other ultrasonic meters.

In applications where insufficient “reflectors” exist (a condition indicated by a low reading on the FD-7000’s Flow Analyzer bar graph), the transducers are relocated to a point in the piping where non-symmetrical hydraulic turbulence will be present – ideally just downstream of a 90-degree elbow. The FD-7000’s unique digital filtering system and signal recognition circuitry transforms the reflections from this non-symmetrical, and not necessarily linear, turbulence into a useable and linear data format.


A backlit, 2 line by 20 character, alphanumeric LCD offers simultaneous flowrate and totalizer displays. The FD-7000 is designed for ease of use in the field. Only a few simple keypad entries are required to configure the flowmeter for any given pipe and flow measurement application. The encapsulated, submersible design of the transducer sensor head allows it to be easily mounted to the pipe surface with the coupling compound and elastic bands that are supplied with the unit.

A 20 ft. (6 meter) retractable cable for connection to the transmitter/indicator unit is supplied as as integral part of the sensor. The FD-7000 sensor is utilized on pipes that range in internal diameter from 25 to 3048 mm (1 to 120"). Flowrates can be measured in smaller pipes from 6 to 25 mm ( 1 /4 to 1") in diameter with use of the small pipe sensor, model FD-7000-S1. These units are not to be used for distilled water or ultra clean water applications.

Ultrasonic Flowmeter FD-7000 is made in USA and advertised at www.omega.com.

SPECIFICATIONS

System Accuracy:
±2% of F.S.

Velocity Range:
0.15 to 6.2 meters/second (0.5 to 20 feet/second)

Measuring Units:
FPS, GPM, MGD

Linearity:
±0.2% of F.S.

Repeatability:
0.4% of F.S.

Flow Rate Display:
6-digit LCD

Totalizer Display:
6-digit LCD (resettable)

Outputs:
4 to 20 mA into 600 Ohms max., isolated

Power Requirements:
115 Vac ±10%, 50/60 Hz, 20 VA max. (standard); 230 Vac 50/60 Hz (optional). Internal gel cell battery provides 8 hrs. of continuous operation

Liquid Requirements:
Full-pipe, low-viscosity (water-like) liquid

Transmitter/Indicator Operating
Temperature:
-30 to 70°C (-22 to 158°F)

Sensor Operating Temperature:
-40 to 121°C (-40 to 250°F)

Dimensions:
432 L x 279 W x 203 mm H
(17 x 11 x 8")

Weight:
10 kg (22 lb)

Enclosure:
NEMA-4X (IP65)

Read more...

Portable Doppler: Ultrasonic Flowmeter, FD613

The FD610 Series ultrasonic flow meter is made in USA and advertised at www.omega.com. It has features advanced Trans-Phase measuring technology, providing accurate and reliable flow velocity assessments in closed piping systems. The FD610 Series utilizes a non-invasive clamp-on transducer which is placed on the outside of a pipe. Within seconds, the large 18 mm (0.7") LCD provides stable flow rate readings in feet per second or meters per second. This product operates on metal or plastic pipes containing liquids with more than 100 ppm of 100 micron or larger suspended solids or entrained gases.

PRINCIPLE OF OPERATION

The FD610 Series flow meter utilizes an advanced Trans-Phase measuring technique, providing accurate, non-invasive fluid velocity assessment without opening the pipe. The FD610 Series utilizes two piezoelectric crystals contained within one transducer to transmit ultrasonic energy into the fluid stream and receive back energy reflected off discontinuities (suspended particles or entrained gases) within the moving liquid. Transformations that result from the energy reflections are processed and converted to a measurement of fluid velocity by the sophisticated software algorithm. The processor also controls all operations of the instrument from its ultra-efficient battery management circuitry to a proprietary FIR (Finite Impulse Response) filtration program.

SPECIFICATIONS

Supply Voltage:
Battery powered, non-rechargeable alkaline, four AA cells, providing over 30 hours of continuous operation

Flow Range:
0.30 to 30.00 FPS (0.10 to 9.00 MPS)

Display:
Single line – four-digit LCD readout of velocity (18 mm (0.7") digits), signal strength, measuring units, and low battery indication

Temperature:
-20 to 60°C (-28 to 140°F)

Enclosure Rating/Dimensions:
NEMA-12X ABS plastic; 200 H x 100 W x 38 mm H (7.76 x 4 x 1.5")

Weight: 0.7 kg (1.5 lb)

Accuracy: ±2% full scale

Transducer
Transducer Material:
Plated body; ULTEM 1000 sensor material

Cable: 2 m (6.6 ft) cable and connector

Temperature: -40 to 82°C (-40 to 180°F)

Humidity: 0 to 95% non-condensing
Mounting Method:
Clamp-on style with DOW 111 coupling compound

Read more...

Fetal Monitoring Transducers from Hewlett Packard

They are advertised by Sun Coast Medica that offering brand new Corometrics® and Hewlett Packard® compatible Tocotransducers and Ultrasound Transducers at a fraction of the original manufacturer's cost!

Keep Mom and Baby working together with our Ultrasound Transducer and relax Mom while measuring Baby's heartbeat during labor. The "Leg Plate" and fetal scalp electrodes are used when it is otherwise difficult to hear the heartbeat with the external Ultrasound Transducer. Volume discounts are available upon request.

• Corometrics® Tocotransducer Model 2260
• Corometrics® Ultrasound Transducer Models B5600, 5700
• Hewlett Packard® Tocotransducer Model M1355A
• Hewlett Packard® Ultrasound Transducer Model M1356A
• Hewlett Packard® Ultrasound Transducer Model 15245A
• Brand New
• One-Year Warranty!

Read more...

TRADEWIND 3000 8" ALTERNATING PRESSURE MATTRESS

The TRADEWIND 3000 is one of the most advanced systems in the TRADEWIND series. The microprocessor pressure sensor technology provides smart pressure auto-checking feature to maximize patient's comfort. This replacement mattress, which offers a low air loss therapy, is consisted of 20 8 inches high cell-in-cell designed air bladders. The patented cell-in-cell design allows the inflation and deflation of air cells to be achieved in the shortest amount of time while providing the good pressure dispersion. The inner cell also offers a sufficient weight support during a power failure. Mattress will remain inflated for up to 24 hours in the event of a power outage. For ease of care taking, the mattress can be easily changed back to flat surface (static mode) within a very short period of time.

This elite mattress will heal existing bedsores and it will also prevent new sores from forming.

This mattress will eliminate having to turn the patient at night.

Product Description:

Features Low air loss, alternating pressure relief therapy Adjustable comfort range with easy operating control knob Static function can suspend the alternating mode (has auto-recovery feature) Microprocessor pressure sensing technology to produce low pressure support Emergency CPR and quick connector for easy operation Visible and audible alarms with Alarm Mute feature (3 minute auto-return feature) Large air filter intake and zipper-all-around cover for easy maintenance Transport mode by interconnecting quick connectors Spring loaded tube to prevent any kinks for smoother airflow Head pillow feature Carry bag (optional) Slip-resistant mat and securing straps on the mattress base for added safety Vapour permeable, water resistant cover (with optional stretched cover)

8" Alternating Mattress Replacement System with Sensor Technology to provide alternating pressure and low air loss.

This system offers a comfort controlled variable pressure, a maximum inflate feature that will inflate the mattress in just minutes and a power failure and low pressure warning lights.

The tradewind 3000 mattress meets the requirements of the HCPCS codes EO277 and E0372.

This mattress will remain inflated in the event of a power outage for up to 24 hours

It is 18 month warranty.

Read more...

ECG Machine: Philips PageWriterTouch

This ECG Machine is designed for high volume hospital in which the quality and accuracy is critical. A high-resolution 15-inch touch screen of Philips PageWriter Touch ECG clearly displays 10 seconds of all 12 leads, color-coded for signal quality. Preview the full report – waveform and interpretation – before printing to save time and paper.

Philips PageWriter Touch ECG has wireless communication that allow you to quickly download orders and send data to your ECG management system at your hospital all in record time. It also has precision performance and sophisticated ergonomic. This is designed for maneuverability and durability, that the cart is well suited to the hospital environment. Cradle for patient module storage and protection is built into the cardiograph.

What is the Features of this ECG machine? It has:

• ECG signal acquisition of up to 12 leads for both adult and pediatric patients
• R/T (real-time) 12-lead display with ECG “snapshot” feature: - Take ECG snapshots of any data on the screen with the touch of a button - Review snapshots and print ECG reports in a variety of formats
• AUTO 12-lead acquisition
• RHYTHM display and printing (up to 12 leads)
• DISCLOSE five minutes of continuous waveform data for review and printing
• Keyboard with Full alphanumeric capability
• Rechargeable battery records approximately 50 ECGs or 40 minutes of rhythm recording from a single battery charge.

The quality of monitor is good and has indicators include AC noise filtering and color-coded real-time wave form display and loose electrode alerts. This Philips PageWriter Touch ECG is also easy to transfer the result by floppy disk, modem or LAN connection to an ECG management system as well as by fax, and it will be automatically indexed on the cardiograph for quick review.

Read more...

AED 20™ Defibrillator from Welch Allyn Company

Let me talk one of Defibrillator from Welch Allyn Company. AED 20™ Defibrillator is one of defibrillator produced by Welch Allyn Global

AED 20™ Defibrillator is ideal for health care or Emergency medical Services (EMS) environments with multiple levels of first responders. It provides clear “1-2-3” guidance in administering a preset life-saving shock, plus the ability to monitor heart rhythms and transfer information for continuous patient data collection.

Important specifications are :

• Text and voice instructions that will guide the user through the rescue
• Color-coded pads and illustrations that make the user ensure proper pad placement
• There is an escalating energy (200 J, 300 J, 360 J); energy protocol can be changed to meet specific needs
• Diagnostic-quality ECG display and lead II monitoring using traditional snap-based electrodes
• The optional passcode that protects manual defibrillation
• Choice of rechargeable battery for frequent users or a long-life nonrechargeable battery for infrequent rescuers

The complete specifications of AED 20™ Defibrillator as mentioned in product document are :

• Dimensions: 9.4"L x 8.9"W x 3.3"H (23.9L x 22.6W x 8.4 H cm)
• Weight: Less than 5.4 pounds (2.45 kg) without battery
• Operating temperature: 32 ºF to 122 ºF (0 ºC to 50 ºC)
• Storage temperature (without battery): -22 ºF to 150 ºF (-30 ºC to 65 ºC)
• Humidity: Up to 95% (non-condensing)
• Altitude: -500 to 15,000 feet (-150 to 4570 m)
• Shock :Mil Std 810E method 516.4, procedure 1 (40G, 6-9 ms pulse, 1/2 sine each axis)
• Vibration: Mil Std 810E method 514.4, category 10 (minimum integrity test for helicopters)
• Water resistance: IEC 60529 IPX4
• In-flight use: Complies with RTCA/DO-160E, Section 21, Category M limits for radio frequency interference
• Event documentation: Internal and via Welch Allyn Datacard
• Internal memory capacity: 1MB: 75 4-sec ECG samples or 500 time-stamped events
• Datacard capacity: 4MB: 90 min of Continuous ECG and 40 min of ECG and audio. 8MB: 3 hrs of Continuous ECG and 80 min of ECG and audio, 16MB: 6 hrs of Continuous ECG and 2.5 hrs of ECG and audio
• Playback: Welch Allyn PIC or Smartview
• Quick report: Treatment Summary, Event Log, Test Log
• Datacard compatibility: Compatible with Welch Allyn PIC Advance Life Support Defibrillator
• Communication: Serial port via RS-232 to PC and printer
• Output: Biphasic Truncated exponential
• Energy sequence (user configurable): Shock 1: 150 J, 200 J, Shock 2: 150 J, 200 J, 300 J, Shock 3: 150 J, 200 J, 300 J, 360 J
• Manual energy selection: (J) 2, 5, 7, 10, 20, 30, 50, 70, 100, 150, 200, 300, 360
• Automatic energy selection: (J) 2, 5, 7, 10, 20, 30, 50, 70, 100, 150, 200, 300, 360
• Manual lockout: Via passcode
• Charge time to maximum energy (manual operation): Frequent use: Less than 8 seconds with a fully charged battery; Less than 8 seconds with a battery depleted by 15 maximum-energy discharges. Infrequent use: Less than 8 seconds with a battery depleted by six maximum energy discharges; Less than 8 seconds with a battery depleted by 15 maximum energy discharges.
• Charge time to maximum energy from initially switching power on, or from within any operator programming mode (manual operation): Frequent use: Less than 25 seconds with a battery depleted by 15 maximum energy discharges. Infrequent use: Less than 30 seconds with a battery depleted by six maximum energy discharges; Less than 35 seconds with a battery depleted by 15 maximum-energy discharges.
• Charge time to maximum energy from activation of the rhythm recognition detector (AED operation): Frequent use: Less than 30 seconds with a battery depleted by 15 maximum energy discharges. Infrequent use: Less than 35 seconds with a battery depleted by six maximum energy discharges; Less than 40 seconds with a battery depleted by 15 maximum-energy discharges.
• Charge time to maximum energy from initially switching power on, or from within any operator programming mode (AED operation): Frequent use: Less than 40 seconds with a battery depleted by 15 maximum energy discharges. Infrequent use: Less than 45 seconds with a battery depleted by six maximum energy discharges; Less than 50 seconds with a battery depleted by 15 maximum-energy discharges.
• Analysis time: 12 to 16 sec.
• Audible prompts: Minimum of 20 audible prompts
• Visual prompts: Minimum of 13 text screen prompts
• Controls: 2 buttons - On/Off, Discharge, and 4 software-configurable buttons

Read more...

Waveline Vital Signs Monitor from DRE

This Waveline Vital Signs Monitor has 6 Parameters: ECG, Respiration, Dual Temperature, Pulse Oximetry, NIBP, Dual Invasive Blood Pressure, Capnography.

With the display in High-resolution color TFT and size 10.4’’ (diagonally) this machine can help a professional health to monitor patient’s vital sign accurately. This waveline vital Sign Monitor also has resolution 640 x 480 pixel, the excellent viewing from distance and angle. Waveform Field: Configurable screen for max. four waveforms (ECG, SPO2, Respiration, Invasive Blood Pressure or CO2)

This medical equipment has features (as mentioned by company):

• Upgradeable monitor with maximum 7 parameters
• High resolution 10.4” (diagonally) color TFT display
• Multi-lead ECG monitoring
• In-built cautery and defibrillator protection
• 24 hr. graphical/tabular trends with zoom facility with separate trend for storing
• 240 NIBP readings
• Graded and color coded alarms with audio/visual indicators
• Alarm recall facility to view last 16 stored critical alarms (patient related)
• Demo mode for training the staff
• Optional dual channel thermal array recorder
• Comprehensive patient data entry
• Mains and battery operation [in-built or external battery (12V)]
• Facility to interface with Slave monitor for remote display
• RS-232 connectivity

As additional information here is the specification of this medical equipment (as mentioned by company):

• Dimension: 202 x 310 x 230 mm (H x W x D)
• Weight: 7.5 kg with in-built batteries. Direct interface possible with color central station. Slave display option possible.
• Power Supply: Universal Power: 95-265V AC, 50/60Hz
• Power Ratings: 40W
• Battery Type: 12V 4 Ah lead acid
• Operating Time: In-built rechargeable batteries for 30 min. of continuous operation under full charge condition (fully loaded, NIBP 2 min. & recorder ON for 2 min.)
• Charging Time: 12 hrs. (Typical) ambulatory monitoring possible with car battery interface.
• External Battery: 12 V 2A (min.)

Read more...

Infant - Pediatric Ventilator from Sechrist Industries, Inc

The Millennium® - the infant ventilator and pediatric ventilation system from Sechrist Industries, Inc. was designed for maximum performance and user-friendly convenience.

The Millennium® Infant Ventilator is a simple, reliable ventilation for neonatal, infant, and pediatric patient requirements. It has a unique pressure sensing device that synchronizes the patient's natural breathing cycle with the neonatal ventilator as well as a maximum sensitivity of 0.10 cmH20, and a response time of 5-40 milliseconds depending upon the sensitivity settings.



TECHNICAL SPECIFICATIONS (as mentioned on company's brochure)

Recommended Applications
Neonatal, infant& pediatric patients < style="font-weight: bold;">Flow
2-32 lpm; flush 40 lpm

Modes of Operation
AC, SIMV/IMV, CPAP, CPAP with backup ventilation, Standby

Inspiratory Time
0.1 to 3.0 seconds


I : E Ratio
Normal Range:
1:1.0 to 1:10 (sens. off)
1:1.0 to 1:99 (sens. on)
Inverse Range:1.0:1 to 4.0:1

Rate
2 to 150 breaths per minute

Expiratory Pressure
0 to 20 cmH2O

Inspiratory Pressure
5 to 70 cmH2O

Waveform
Tappered to square

Manual Breath
Electronically controlled, based upon the inspiratory pressure, inspiratory time and waveform control setting

Alarms

• High Inspiratory Pressure
• Low/Prolonged Inspiratory Pressure
• Low PEEP/Baseline Pressure
• Apnea
• High Respiratory Rate
• Loss/Low Electrical Power
• System Error/Vent Inop
• Loss of Inlet Gas

Alarm Delay Time
3 to 15 seconds

Alam Mute
30 Seconds

Safety Pressure Relief Valve
15 to 85 cmH20

Indicators

• Inspiratory Pressure
• PEEP/Baseline Pressure
• Calculated I:E Ratio
• Mean Airway Pressure
• Proximal Airway Pressure Bar Graph
• Measured Respiratory Rate

Dimensions

• 13.5"(34.29cm)H
• 11"(27.94cm)W
• 9.5"(24.13cm)D

Weight
21 lbs (9.5kg)

Gas Consumption
14 lpm above the continuous flow setting

Power Requirements

• 110 to 120 VAC, 50/60 Hz
• 220 to 240 VAC, 50/60 Hz
• 100 VAC, 50/60 Hz

This Medical Equipment will help people to improve a life.

Read more...

The HeartStart FR2+ Defibrillator from Philips

As the definitive treatment for the life-threatening cardiac arrhythmias ventricular fibrillation and pulseless ventricular tachycardia, defibrillatior consists of delivering a therapeutic dose of electrical energy to affect the heart to be worked. It depolarizes a critical mass of the heart muscle, terminates the arrhythmia, and allows normal sinus rhythm to be reestablished by the body's natural pacemaker, in the sinoatrial node of the heart.

Defibrillators can be external, transvenous, or implanted, depending on the type of device used. Some external units, known as automated external defibrillators (AEDs), automate the diagnosis of treatable rhythms, meaning that lay responders or bystanders are able to use them successfully with little, or in some cases no, training.

There are so many companies produced Automatic External Defibrillator. Koninklijke Philips Electronic N.V. is one of them who produces a Automatic External Defibrillators. They produce a HeartStart FR2+ Defibrillator.


The HeartStart FR2+ Defibrillator has come to be a trusted tool of professional responders and designated response teams in the workplace and public settings. Its clean, uncluttered design is optimized for fast, efficient operation and rapid delivery of life-saving therapy. Commands are clear, streamlined, confident, and concise: ideal for responders who are trained, drilled, and ready to save a life now.

Here is the feature of HeartStart FR2+ Defibrillator:

• Biphasic therapy
• Automated defibrillation, with manual override
• SMART Analysis
• SMART CPR and Quick Shock
• Pediatric defibrillation (infant/child pads)
• Conscious monitoring (3-Lead ECG, optional)
• Two display options: text-only, and text with ECG
• Voice and text prompts
• Data collection and programmable voice recording
• Automated self-tests
• "Ready-for-Use" indicator
• Long-life battery: 300 shocks (min.) or 12 hrs. monitoring

Read more...